Anycubic PLA Silk Tri-colour Filament 1kg – Red/Blue/Yellow

What this part is

<p><strong>Tri-colour silk gradient in one spool | Silky lustrous finish | Compatible with 0.4 mm nozzles and above | Print speeds up to 250 mm/s | Supports intelligent filament identification</strong></p> <p>The Anycubic PLA Silk Tri-colour Filament in Red, Blue, and Yellow is designed for makers who want to elevate decorative prints, fan art, and artistic models beyond single-colour results. Three colours are blended into a single 1 kg spool, producing smooth gradient transitions and a silk-like lustrous finish that shifts visually as the model is rotated. You can fine-tune the surface gloss by adjusting nozzle temperature and print speed — a higher temperature or slower speed increases fluidity and produces a higher-gloss, smoother surface, while cooler or faster settings give a subtler sheen. Compatible with any FDM printer that accepts 1.75 mm filament and a nozzle of 0.4 mm or above, it runs at printing temperatures of 210–240 °C, a heated bed of 55–56 °C, and recommended speeds of 50–250 mm/s. On compatible Anycubic printers the intelligent identification chip is read automatically, streamlining setup without any manual input. A reliable, visually striking choice for decorative and display-quality 3D prints.</p> <h3>Features</h3> <ul> <li>Tri-colour gradient (Red, Blue, Yellow) blended in a single 1 kg spool for layered, multi-tone prints</li> <li>Silk-like lustrous finish that shifts appearance with viewing angle</li> <li>Adjustable gloss — tune nozzle temperature (210–240 °C) and print speed (50–250 mm/s) to control surface sheen</li> <li>Compatible with all 1.75 mm FDM printers using a 0.4 mm or larger nozzle</li> <li>Intelligent identification chip for automatic filament recognition on compatible Anycubic printers</li> <li>Suited to decorative parts, fan art, figurines, and display models</li> </ul> <h3>Specifications</h3> <ul> <li>Colour: Red Blue Yellow (#003594,#F3D03E,#D22630)</li> <li>Dry Out Before Use: Recommended</li> <li>Drying Condition: 55-65℃, 6-8h</li> <li>ACE Compatibility: Compatible</li> <li>Nozzle Size: Recommended 0.4 mm or above</li> <li>Printing Temperature: 210-240 ℃</li> <li>Heated Bed Temperature: 55-56 ℃</li> <li>Recommended Printing Speed: 50-250 mm/s</li> <li>Maximum Volume Speed (Flow Rate): 8 mm³/s</li> <li>Density: 1.22 g/cm³</li> <li>Melt Index: 9±1 g/10 min (190℃/2.16kg)</li> <li>Melting Point Temperature: 164 ℃</li> <li>Vicat Softening Temperature: 54 ℃</li> <li>Heat Deflection Temperature (0.45MPa): 53 ℃</li> <li>Young’s Modulus: 2000±200 MPa</li> <li>Tensile Strength: 37±4 MPa</li> <li>Elongation at Break: 28±5%</li> <li>Bending Modulus: 2400±160 MPa</li> <li>Bending Strength: 66±4 MPa</li> <li>lzod lmpact Strength (X-Y): 20±2 kJ/m²</li> <li>Tensile Strength (Z): 12±4 MPa</li> <li>Filament Type: Aesthetic filaments</li> <li>Recommend to Print: Decorative parts, fandom, artworks</li> <li>Intelligent Identification: Supported</li> <li>Reusable Filament Spool: Supported</li> <li>Size: 1KG</li> </ul> <h3>What's in the Box</h3> <ul> <li>Anycubic PLA Silk Tri-colour Filament 1kg – Red/Blue/Yellow x1</li> </ul>